Denver, Colorado Calibration Lab

Industry-leading turnaround times

location/acute

Multiple specialty capabilities

location/oscilloscope

Accredited calibrations to ISO/IEC 17025:2017

location/architecture

Expedited service available

location/shipping

In-lab and onsite services available

location/location

Transcat's primary torque lab

location/tool

Welcome to our Denver calibration lab located in Aurora, CO about 30 minutes from the Denver International Airport. This fully capable general-purpose lab is ISO/IEC 17025:2017 Accredited and is also Transcat’s primary torque lab.

Accreditations at our Denver Lab 

• ISO/IEC 17025:2017
• ANSI/NCSL Z540-1-1994 (R2002)
• IANSI/NCSL Z540.3-2006 (R2013)

location/pdf

Transcat Calibration Services

3251 Lewiston St #12
Aurora, CO 80011

Phone: (303) 364-8325

[email protected]

Did you Know?

We perform calibrations in lab and onsite through the region.

Our Denver lab calibration lab has specialty capabilities such as RF microwave up to 26.5GHz, high voltage measurements up to 85kVAC/120kVDC, oscilloscopes up to 20GHz, logic analyzers, and single and triaxial accelerometers. We also have torque capability to 20000 fb. lb. and pressure calibrations from -36 in H2O to 30,000 psi. 

Request a Calibration Quote
Accredited Calibration Service Capabilities

Transcat offers extensive calibration capabilities covering a broad range of test and measurement including: 

Calibrators

Dimensional

  • Dimensional Calibration Services in Denver, CO
  • Calipers Calibration Services in Denver, CO
  • Crimp Tools Calibration Services in Denver, CO
  • Depth Gages Calibration Services in Denver, CO
  • Gage Blocks Calibration Services in Denver, CO
  • Height Gages Calibration Services in Denver, CO
  • Indicators Calibration Services in Denver, CO
  • Micrometers Calibration Services in Denver, CO
  • Parallels Calibration Services in Denver, CO
  • Pin Gages Calibration Services in Denver, CO
  • Protractors Calibration Services in Denver, CO
  • Rulers Calibration Services in Denver, CO

Electrical

Electronic

Flow

  • Air Flow Calibration Services in Denver, CO
  • NEW Liquid Flow Calibration Services in Denver, CO

Liquid Handling

  • Pipettes Calibration Services in Denver, CO

Mass

Physical

Pressure

Temperature

Accredited Reference Level Capabilities

Transcat also offers Reference Level Calibrations in multiple disciplines - with faster turnaround than the OEM. Few commercial calibration operations are equipped with the quality systems that allow Transcat to offer ISO/IEC 17025:2017 accredited reference level calibrations.  Transcat is one of a select few commercial calibration operations qualified to be accredited as a Reference Laboratory in the disciplines of Temperature, Electrical, Pressure, Dimensional, Mass and Humidity. 

Reference Electrical Standards

  • Reference Electrical Standards Calibration Services in Denver, CO
  • DC/Low Frequency Calibration Services in Denver, CO
  • Current Shunts Calibration Services in Denver, CO
  • High Accuracy Digital Multimeters Calibration Services in Denver, CO
  • Multifunction Calibrators Calibration Services in Denver, CO
  • Phase Calibration Services in Denver, CO
  • Precision Capacitors Calibration Services in Denver, CO
  • Precision Inductors Calibration Services in Denver, CO
  • Precision Resistors Calibration Services in Denver, CO

Reference Temperature Standards

Pressure

  • Dead Weight Testers, Pneumatic & Hydraulic Calibration Services in Denver, CO
  • High Precision Pressure Controllers Calibration Services in Denver, CO
  • High Precision Pressure Transducers Calibration Services in Denver, CO
  • Very Low Pressure Installments Calibration Services in Denver, CO

Dimensional

  • Custom Fixturing Calibration Services in Denver, CO
  • Diameter Master Rings Calibration Services in Denver, CO
  • End Measuring Rods Calibration Services in Denver, CO
  • Gage Blocks Calibration Services in Denver, CO
  • Height Masters Calibration Services in Denver, CO
  • Overlays Calibration Services in Denver, CO
  • Pin Gages Calibration Services in Denver, CO
  • Plug Gages Calibration Services in Denver, CO
  • Sine Bars/Plates Calibration Services in Denver, CO
  • Thread Gages Calibration Services in Denver, CO
  • Thread Wires Calibration Services in Denver, CO

Mass

  • Mass Calibration Services in Denver, CO
  • Weights in Classes 1-7 up to 25 kg Calibration Services in Denver, CO
  • Load Cells Calibration Services in Denver, CO
  • Proving Rings Calibration Services in Denver, CO

High Voltage

  • High Voltage Calibration Services in Denver, CO
  • AC (0 to 80k) Calibration Services in Denver, CO
  • DC (0 to 120k) Calibration Services in Denver, CO
  • Probes, Dividers &amp Meters Calibration Services in Denver, CO
Other Metrology Capabilities

Parts inspection and calibration are available with ISO/IEC 17025:2017 Transcat Accredited Quality. In our lab OR onsite at your organization, you can request dimensional analysis for part inspection.  

Learn More about Calibration Services from
Transcat

Discover the full scope of services from Transcat and learn how we support
customers across the globe here.

I have had the pleasure of working, with not only Sean Sheeran, but a large quantity of the Transcat team since my beginnings here in 2017. Everyone I have personally dealt with has been exceptionally helpful and knowledgeable about the products and services offered. If information is unknown, they have always made it a point to go above and beyond to find the answers we are needing while maintaining a timely manner. The calibration paperwork that we receive is always easily understood and obtainable. The online system has been a tremendous asset to our company as I am sure it has to theirs. Sometimes the calibration certs seem to have legs and walks off with the equipment owners here, so having a means to reprint and/or view them is great.

Sam Roubdioux, Facilities & Site Coordinator, Evonik

Request a Calibration Quote

Your request will be assigned to a member of our expert sales and customer service team. You should receive a response within 24 hours. If you need immediate assistance, please call us at (800) 828-1470.

Request a Calibration Quote